武汉赛林德船舶科技有限公司

SAILINDE MARINE TECHNOLOGY (WUHAN)CO.,LTD.
联系我们
 工作时间
周一至周五 :8:00-17:00
 联系方式
电话:027-86633188
传真:027-86633288
邮编:430205
地址:湖北省武汉市东湖新技术开发区佛祖岭一路9号
产品详情
船用电控气缸注油器系统
船用电控气缸注油器系统
产品详情

系统构成与系统特点

System constitution and Characteristics

系统包括油泵单元,主控单元及切换装置

The system consists of the oil pump unit ,master control unit and safety interlock.

电控注油模式能节省气缸油30%~40%减少缸套的磨损,延长主机缸套使用寿命,减少缸套污油的排放量,减少污油处理费用,利于环保,安全联动装置将机械注油器设为安全备份,使系统工作安全可靠。

浙江体彩Electronic controlled lubrication mode can:save30%~40% cylinder lUbe oil, Decrease cylinder liner`s wear rate, prolong theservice life of main engine`s cylinder liners, Reduce the sludge emission,reduce sludge treatment costs and benefit to environmental protect, Safetyinterlock sets the mechanical lubricator as safety backup, as a resulf, thesystem can work more safely.


浙江体彩主控单元Mastercontrol unit

主控制单元由主控制系统(MCS)辅控报警系统(ACAS)以及供电系统(PSS)组成,所属设备包括操作面板(OP),主控箱(MCB),供电箱(PDB)及外围设备(PE)组成。

The main control unit is composed of MCS(Main Control System),ACAS(Auxiliary Control and Alarm System) and PSS (PowerSupply System), The equipment of the main control unit consists of OP(Operation Panel), MCB (Main Control box),Pdb (Power Distribute Box), and PE(Peripheral Equipment).


浙江体彩主控制单元接受来自角度编码器的主机曲轴转角信号(下止点信号),主机转速信号和来自负荷指示传感器的主机负荷信号以及燃油的含硫量等数字信号,根据设定的控制模式,经过计算后给出注油定时和注油频率,控制步进电机动作以实现气缸油的准确注入。

The main control unit of electronicallycontrolled lubricator receives the signal of main engine crank angle from theanglo encoder (the BDC signal), main engine speed, the main engine load fromthe load instruction sensor, fuel sulfur content and other digital signals ,andthen works out the injection timing and frequency according to the set controlmod,controls a stepper motor action and achieve the accuracy of eylinder oilinjection.


切换装置Safetyinterlock

在电控注油系统工作时,机械式注油器所泵送的气缸油被旁通回到油箱,此时电控注油器向气缸注油;当电控注油系统故障全部或部分停止工作时,通过改变滑阀芯轴的位置,使机械式注油器向气缸注油,而电控注油系统不注油或回流到油箱。

When the electronically controlled cylinderlubrication systems is working cylinder oil pumped by the mechanical lubricatorwill bypass back to the tank, the electronically controlled lubricator injectsoil to the cylinder; If the electronically controlled cylinder lubricationsystem is failed to work in whole or in part ,micro-air motor will change theposition of the sliding spool shaft, the mechanical lubricator will fulfill thecylinder oil injection, the electronically controlled lubricator is notworkiing or sends oil back to the tank.


浙江体彩油泵单元Oil pump

油泵单元由高精度专用柱塞油泵和步进电机组成,步进电机接受主控单元信号,控制并驱动油泵,将已标定的主机缸套油,精确地注入标定的主机活塞环及环槽区域。

The oil pump unit is composed of dedicatedhighaccuracy plunger oil pump and stepper motor, The stepper motor receivessignals from the master control unit, Controls and drives the oil pumpprecisely injects the calibrated dose of cylinde oil onto the main enginepiston rings and ring groove area.